| 1475cc Stroker crank, Gas Flowed Head, Cams, etc. 205hp rear wheel | |||
| 71.5mm stroker crank and arrow conrods (1475cc with 81mm bore) | £2,100.00 | ||
| Gas Flowed Head including 3 angle cut seats etc. | £350.00 | ||
| Reprofiled High Lift Camshafts including adjustable sprockets | £300.00 | ||
| Gaskets | £60.00 | ||
| Valve shims | £60.00 | ||
| Engine work labour to strip & rebuild, dial in cams, set valve clearances, etc. | £800.00 | ||
| Total = | £3,670.00 | ||
| 1475cc (81mm stock bore, high compression piston kit), Gasflowed head, Cams, etc, 210hp rear wheel | |||
| 71.5mm stroker crank and arrow conrods (1475cc with 81mm bore) | £2,100.00 | ||
| High Compression Piston Kit | £380.00 | ||
| Gas Flowed Head including 3 angle cut seats etc. | £350.00 | ||
| Reprofiled High Lift Camshafts including adjustable sprockets | £300.00 | ||
| Valve shims | £60.00 | ||
| Gaskets | £60.00 | ||
| Engine work labour to strip & rebuild, dial in cams, set valve clearances, etc. | £800.00 | ||
| Total = | £4,050.00 | ||
| 1585cc (84mm big bore, high compression), Gasflowed head, Cams, etc. 220hp rear wheel | |||
| 71.5mm stroker crank and arrow conrods (1585cc with 84mm bore) | £2,100.00 | ||
| High Compression Piston Kit | £380.00 | ||
| Cylinder block, boring, replating to suit new oversize pistons | £450.00 | ||
| Gas Flowed Head including 3 angle cut seats etc. | £350.00 | ||
| Reprofiled High Lift Camshafts including adjustable sprockets | £300.00 | ||
| Valve shims | £60.00 | ||
| Gaskets | £60.00 | ||
| Engine work labour to strip & rebuild, dial in cams, set valve clearances, etc. | £800.00 | ||
| Total = | £4,500.00 | ||
| Other Available Performance Parts:- | |||
| 71.5mm stroker crank and arrow conrods | £2,100.00 | ||
| Billet Race Camshafts including adjustable cam sprockets | £500.00 | ||
| Carillo / Arrow Conrods | £700.00 | ||
| Heavy Duty Valve Springs | £150.00 | ||
| High Ratio 5th and 6th gears | £450.00 | ||
| Adjustable Press on Cam Sprockets | £140.00 | ||
| 10mm Heavy Duty Cylinder Head Studs and nuts | £80.00 | ||
| 12mm Extra Heavy Duty Cylinder Bolts and spacers | £60.00 | ||
| 1/2 inch Super Heavy Duty Cylinder Head Studs and nuts | £150.00 | ||
| Heavy Duty Crankcase studs and nuts | £70.00 | ||
| Billet manual camchain tensioner | £40.00 | ||
| Heavy Duty Starter Idler Gear | £100.00 | ||
| Billet starter idler assembly with sprag clutch idler gear and cases | £280.00 | ||
| Billet high capacity oil pump | £220.00 | ||
| Billet Clutch Centre | £140.00 | ||
| Dynojet Powercommander3USB | £220.00 | ||
| Koenig Billet sump with swivel pick up (50mm more ground clearance) | £320.00 | ||
| sump baffle plates (st.steel) | £50.00 | ||
| Crankshaft Balance with pistons and conrods | £150.00 | ||
| Crankshaft Lighten, Knife-edge, remove balancer gear, balance with pistons & conrods | £250.00 | ||